My E11 Blaster Build.WIP

Ideas, tutorials, questions relating to armour, costumes and replica props from the Star Wars universe
User avatar
batmanreturns
Ensign
Ensign
Posts: 63
Joined: Sun Aug 24, 2014 2:46 am
Country: new zealand

Re: My E11 Blaster Build.WIP

Post by batmanreturns »

stunning commitment to attention to detail. :cool:
"never be afraid to raise your voice for honesty and truth and compassion against injustice and lying and greed. if people all over the world would do this....it would change the earth." -w.faulkner.
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

Thanks for that batmanreturns. I am enjoying doing this.
Attachments
20171203_172326.jpg
20171203_172326.jpg (566.51 KiB) Viewed 37111 times
Once that was done,I folded the top edges to fit into the top of the grip. After test fitting in the grip I cut a piece of MDF and glued it in-between the bottom of the two sides of the mount
Once that was done,I folded the top edges to fit into the top of the grip. After test fitting in the grip I cut a piece of MDF and glued it in-between the bottom of the two sides of the mount
20171203_172318.jpg (593.56 KiB) Viewed 37111 times
Next step is to cut out this template for the grip mount and fold up and clean the edges
Next step is to cut out this template for the grip mount and fold up and clean the edges
20171202_135929.jpg (586.54 KiB) Viewed 37111 times
Another closeup
Another closeup
20171118_214653.jpg (642.22 KiB) Viewed 37111 times
Grinding out the inside of the grip
Grinding out the inside of the grip
20171118_214703.jpg (610.91 KiB) Viewed 37111 times
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

More pics of the trigger group as progress is made and a comparison pic of a casting from Oota and the one I made with bought grip added. Note the difference in the guard position. It appears that this was common on some Sterlings. If I rotate the guard on the housing, it seems to match the position on Oota's casting from an original.
Attachments
20171202_174633.jpg
20171202_174633.jpg (605.19 KiB) Viewed 37047 times
20171202_173708.jpg
20171202_173708.jpg (553.48 KiB) Viewed 37047 times
20171202_173600.jpg
20171202_173600.jpg (528.38 KiB) Viewed 37047 times
20171202_151648.jpg
20171202_151648.jpg (871.72 KiB) Viewed 37047 times
20171202_151706.jpg
20171202_151706.jpg (803.58 KiB) Viewed 37047 times
User avatar
oota goota
High Colonel
High Colonel
Posts: 1908
Joined: Tue Mar 23, 2010 12:08 am
Country: New Zealand
Location: Taranaki
Contact:

Re: My E11 Blaster Build.WIP

Post by oota goota »

wow Nick you have gone next level on this e-11 well done!
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

Thanks Oota. I have modified the Folding Stock Frame as well.
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

Here are some more pics
Attachments
Together again for a test fit.
Together again for a test fit.
20171203_175255.jpg (568.73 KiB) Viewed 37034 times
Another shot.
Another shot.
20171203_172318.jpg (593.56 KiB) Viewed 37034 times
Using blocks of MDF to sandwich between the left and right sides of the grip handle
Using blocks of MDF to sandwich between the left and right sides of the grip handle
20171203_164337.jpg (547.16 KiB) Viewed 37034 times
20171202_175012.jpg
20171202_175012.jpg (566.12 KiB) Viewed 37034 times
Using a center punch to position hole for trigger grip retaining pin
Using a center punch to position hole for trigger grip retaining pin
20171202_175037.jpg (754.23 KiB) Viewed 37034 times
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

Thought I would post some more pics to keep up with construction.
Attachments
I am now working on the Folding Stock. Here I have replaced the cast arms with those made from Aluminium for strength.
I am now working on the Folding Stock. Here I have replaced the cast arms with those made from Aluminium for strength.
20171210_105605.jpg (532.21 KiB) Viewed 37010 times
20171205_121007.jpg
20171205_121007.jpg (651.72 KiB) Viewed 37010 times
Made the selector by cutting a groove in the top of a Cap Screw and then gluing the plate into it. The grooves in the plate were done with a cutting disc.
Made the selector by cutting a groove in the top of a Cap Screw and then gluing the plate into it. The grooves in the plate were done with a cutting disc.
20171205_114321.jpg (646.86 KiB) Viewed 37010 times
20171203_172318.jpg
20171203_172318.jpg (593.56 KiB) Viewed 37010 times
I used a 3mm letter punch set to mark out the A R and S but I will need to do them again to try and get them crisp.
I used a 3mm letter punch set to mark out the A R and S but I will need to do them again to try and get them crisp.
20171202_175012.jpg (566.12 KiB) Viewed 37010 times
User avatar
Blaxmyth
Commander
Commander
Posts: 231
Joined: Fri Oct 08, 2010 9:13 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by Blaxmyth »

Very nice work with the selector lever!
User avatar
MattG
Site Admin
Site Admin
Posts: 4921
Joined: Tue Nov 10, 2009 5:46 am
Country: New Zealand
Location: Auckland

Re: My E11 Blaster Build.WIP

Post by MattG »

That's some next level detailing.
User avatar
TIE1138
Lieutenant
Lieutenant
Posts: 120
Joined: Sat Aug 08, 2015 10:02 am
Country: New Zealand
Location: Wanganui

Re: My E11 Blaster Build.WIP

Post by TIE1138 »

Thanks guys. I am nearly finished would you believe. :D
Attachments
Starting to bend and shape the flats. Ali works so nicely when distressing.
Starting to bend and shape the flats. Ali works so nicely when distressing.
20171209_155844.jpg (520.27 KiB) Viewed 36992 times
Both sides done ready for the Aluminium flats
Both sides done ready for the Aluminium flats
20171205_152038.jpg (516.44 KiB) Viewed 36992 times
Filing down the sides of the cast stock frame
Filing down the sides of the cast stock frame
20171205_151541.jpg (862.13 KiB) Viewed 36992 times
The new improved trigger guard made of thicker Ali.
The new improved trigger guard made of thicker Ali.
20171203_175255.jpg (568.73 KiB) Viewed 36992 times
20171203_173608.jpg
20171203_173608.jpg (458.15 KiB) Viewed 36992 times
Post Reply